top of page

Edge Protection Requirements QLD: What Builders Need to Know

Hasscaff
Nov 5
10 min read

Updated: Nov 7

Last reviewed: 4 November 2026 Location: Queensland, Australia


Temporary guardrails installed along the exposed perimeter of a roof-level structure during construction.
Temporary guardrails installed along an exposed roof-level perimeter to help reduce the risk of falls during construction.

Edge protection is an important fall prevention measure on construction sites, particularly where workers need to carry out tasks near exposed roof edges, elevated platforms, floor openings or unfinished building structures. In Queensland, builders and contractors must identify fall hazards and implement appropriate control measures under workplace health and safety requirements.

Understanding edge protection requirements in QLD helps construction businesses plan suitable protection before work begins. The right arrangement depends on the building, the height and location of the work, the supporting structure and the activities being carried out. Hasscaff supplies, installs and dismantles scaffolding and access solutions for residential and commercial projects across South East Queensland.

This guide explains the relevant Queensland fall prevention requirements, the design considerations for temporary edge protection, and how scaffolding and other protection systems may be used together.



1. What Do Edge Protection Requirements QLD Mean for Builders?

Queensland's workplace safety requirements are set out in the Work Health and Safety Regulation 2011 (Qld). Sections 306C, 306D and 306E address fall risks during construction work and the use of edge protection as a control measure.

Under section 306D, specific fall prevention control requirements apply where there is a risk of a person falling:

  • At least 3 metres during housing construction work.

  • At least 2 metres during other construction work.

  • From a roof or partly completed roof with a slope greater than 26 degrees, regardless of the height threshold.

These requirements do not mean that every site must use the same edge protection system. The regulation requires appropriate fall prevention controls, with fall-arrest controls used where preventing the fall is not reasonably practicable. Edge protection is one recognised fall prevention measure.

Section 306C also addresses fall risks below the specified height thresholds and on roof surfaces with a slope not greater than 26 degrees. A lower working height does not automatically remove the duty to identify hazards, assess the risk and implement appropriate controls.

There is also a separate requirement concerning Safe Work Method Statements (SWMS). Construction work involving a risk of a person falling more than 2 metres is classified as high-risk construction work under sections 291 and 299 of the WHS Regulation. A SWMS must be prepared for that work, including housing construction work where the fall risk is more than 2 metres but below the 3-metre housing threshold.

For practical guidance, builders can refer to WorkSafe Queensland's construction guidance on working at heights and Safe Work Australia's working-at-heights guidance. The latter explains the broader risk management approach, while Queensland's legislation and regulator guidance should be used for Queensland-specific requirements.


2. Where Is Edge Protection Required on a Construction Site?

Edge protection is used to reduce the risk of workers falling from exposed edges or elevated work areas. The appropriate arrangement depends on the location of the hazard, the type of work and the protection required.

Common locations where edge protection may be needed include:

  • Roof edges: Exposed roof perimeters where workers carry out roofing, repairs, installation or maintenance.

  • Floor openings: Unprotected openings between floors, service penetrations and other gaps through which a person could fall.

  • Elevated platforms: Temporary work areas where workers need protection along exposed sides.

  • Building perimeters: Upper-level external edges on residential, commercial and multi-storey construction projects.

  • Scaffold working platforms: Exposed sides of scaffold structures where suitable edge protection is required.

The risk assessment should also consider hazards below the work area. A relatively short fall can still cause serious injury if a worker lands on exposed reinforcement, sharp materials, equipment or other obstructions.

For example, roof repair work may involve workers moving along an exposed roof perimeter while handling tools and building materials. Planning scaffolding for roof repairs in Brisbane should therefore consider the required working access, roof design, potential fall paths and suitable protection for the tasks involved.

Understanding the different types of scaffolding can also help builders compare access arrangements for different building configurations and site requirements.


3. What Are the Design Requirements for Edge Protection?

Section 306E of Queensland's WHS Regulation sets out requirements for edge protection when it is used as a fall prevention control measure. These requirements address the system's ability to withstand impact and the arrangement of its protective components.

The edge protection system must be designed to withstand the downward or outward force of the impact of a person falling against it. It must include a rail or another component that prevents people from falling, together with another rail or rails, or sturdy mesh, sheeting or similar material below the protective component.

Where the system uses rails, section 306E specifies the following requirements:

Component

Requirement under section 306E

Protective component

A rail or another component designed to prevent a person from falling must be fitted.

Additional protection

Another rail or rails, or sturdy mesh, sheeting or other material must be fitted below the protective component.

Bottom rail

At least 150 mm and no more than 250 mm above the surface at the base of the edge protection, where this arrangement is used.

Toe board alternative

At least 150 mm high and fitted below all rails.

Rail spacing

No more than 450 mm between adjacent rails, or between the lowest rail and the toe board.

Steep roof surfaces

Where the surface has a slope greater than 26 degrees, sturdy mesh, sheeting or other material must extend at least 900 mm upwards from the base surface or toe board.

Important measurement distinction: The 900 mm requirement above applies to the upward extension of mesh, sheeting or similar material on surfaces with a slope greater than 26 degrees. It should not be interpreted as a universal minimum top-rail height under section 306E.

These statutory requirements are not a complete design specification for every edge protection product or project. The selected system must also be suitable for its intended application, supporting structure, expected loads and installation conditions.

WorkSafe Queensland's guidance on edge protection system requirements provides further information about design, manufacture, testing, installation and the requirements of section 306E. It also highlights the importance of using equipment that is properly designed, installed and maintained.


4. What Standards Apply to Temporary Edge Protection?

Temporary perimeter guardrails installed around the upper edge of a timber-framed structure.
Perimeter guardrails installed around a timber-framed structure, providing a protective barrier along the elevated work area.

Australian Standards provide technical guidance for the design, manufacture, installation and use of safety equipment. For temporary edge protection, the relevant standards include the AS/NZS 4994 series.

The main parts cover different applications:

  • AS/NZS 4994.1:2023 – General requirements: Covers the design, manufacture, installation and testing of temporary edge protection equipment.

  • AS/NZS 4994.2:2023 – Roof edge protection: Covers the selection, installation, use and dismantling of temporary roof edge protection.

  • AS/NZS 4994.3:2023 – Edges other than roof edges: Covers temporary edge protection for openings and other non-roof edges.

  • AS/NZS 4994.4:2018 – Perimeter protection screens: Covers perimeter protection screens attached to buildings or structures.

The 2023 editions of Parts 2 and 3 incorporate Amendment 1:2024. Builders and contractors should check the current editions and amendments in the Standards Australia catalogue for AS/NZS 4994 before specifying or selecting equipment.

Other standards address related but distinct applications:

Scaffolding standards

The relevant parts of the AS/NZS 1576 series address scaffolding equipment and systems. These standards should be considered when scaffolding forms part of a working platform or supports an edge protection arrangement. The scaffold and any additional components must be suitable for the intended configuration and loads.

Fixed access systems

AS 1657:2018 addresses fixed platforms, walkways, stairways and ladders. It is relevant to permanent access infrastructure and associated protection, but it should not be treated as a replacement for the requirements applying to temporary edge protection.

Roof safety mesh

AS/NZS 4389:2015 addresses safety mesh installed beneath roof sheeting. Safety mesh helps manage the risk of falling through fragile roof materials, while perimeter edge protection addresses the separate risk of falling from a roof edge. One should not be assumed to replace the other. WorkSafe Queensland discusses these complementary controls in its guidance on a worker injured after falling through a roof.

Standards, legislation and codes of practice serve different purposes. Builders should consider the applicable legal requirements, relevant technical standards, manufacturer instructions and project-specific engineering advice together rather than relying on a single document.


5. What Should Builders Consider Before Installing Edge Protection?

Planning should begin before workers are exposed to the fall hazard. Selecting a suitable system involves reviewing the work area, the building structure and how different trades will use the site.

Building structure and fixing points

The supporting structure must be suitable for the selected protection system. Fixing points, connections and installation methods should follow the system's design and manufacturer requirements. Where the structure or fixing arrangement is uncertain, obtain suitable technical or engineering advice before installation.

Roof pitch and surface conditions

Roof angle, surface material and geometry can affect the type of protection needed. Steeper roof surfaces may require additional protective components, including mesh or sheeting where the regulation specifies it.

Access and work requirements

The system should allow workers to carry out their tasks without introducing unnecessary obstructions or new hazards. Consider how workers, materials and equipment will move around the site, including access points and areas where trades may work simultaneously.

Ground conditions and scaffold stability

Where scaffolding forms part of the protection arrangement, the supporting ground, foundations, soleboards, baseplates and scaffold ties must be considered. Poor ground conditions, nearby excavations and changes in loading can affect scaffold stability.

Weather and environmental conditions

Wind, rain and slippery surfaces can affect workers and temporary equipment. Site planning should consider expected environmental conditions and whether the system remains suitable throughout the work.

Other trades and changing site conditions

Edge protection should remain effective as construction progresses. Changes to the building, access requirements, working platforms or surrounding activities may require the arrangement to be reviewed.

A useful pre-installation check should establish:

  1. Where the fall hazards are located and who may be exposed.

  2. What work will be performed and how long the protection will be required.

  3. Whether the building or scaffold can support the selected system.

  4. What fixing methods and installation instructions apply.

  5. How the system will be inspected, maintained and adjusted as work progresses.

This approach helps ensure that edge protection is selected for the actual site conditions rather than simply choosing a system based on building height.


6. How Does Edge Protection Work With Scaffolding?

Scaffolding and edge protection can work together to provide safer access to elevated work areas. However, the two systems must be planned as a coordinated arrangement rather than treated as interchangeable equipment.

Scaffolding may provide a working platform and access to different parts of a building, while suitable edge protection helps reduce the risk of workers falling from exposed edges. The design and installation must account for the loads, connections and configuration of both systems.

Queensland's Scaffolding Code of Practice 2021 specifically addresses edge protection in section 3.5.5. It states that written approval from an engineer must be obtained before installing edge protection on a scaffold system that was not originally designed, supplied or manufactured with edge protection. The approval should include specifications for installation and maintenance.

This requirement is important because attaching additional components to a scaffold without confirming that the system can support them may introduce structural and safety risks. Builders should not assume that a standard scaffold can accommodate additional guardrails, screens or other components without the appropriate design checks and approval.

Scaffold planning should also account for foundations, loadings, ties, access and egress, and the activities taking place around the structure. These considerations become especially important on larger buildings where the height, site restrictions and number of trades can make access planning more complex.

For projects involving multi-storey buildings, Hasscaff's high-rise scaffolding planning guide provides further context on the access considerations associated with larger construction sites.


7. Planning Edge Protection for Projects Across South East Queensland

Every construction site has different access and safety requirements. A suitable edge protection arrangement should be assessed against the building design, working height, surrounding conditions and tasks that need to be completed.

Hasscaff provides scaffolding services across Brisbane, the Gold Coast and the Sunshine Coast, supporting residential, commercial and construction projects with access solutions planned around individual site requirements.

For projects requiring temporary perimeter protection or scaffold-supported access, the arrangement should be reviewed before installation to confirm that the selected system is appropriate for the structure and intended work.

Hasscaff's Guardrail and Edge Protection service provides further information about the protection options available for construction and maintenance projects.


Conclusion

Edge protection is an important part of managing fall risks on Queensland construction sites. Builders and contractors need to understand the applicable fall prevention requirements, assess the conditions of the work area and select a system that is suitable for the building and the tasks being performed.

The requirements involve more than selecting a guardrail or barrier. Proper planning should account for the supporting structure, equipment specifications, installation method, access requirements and how the system will be maintained throughout the project.

Where scaffolding is involved, the access structure and protection components should be assessed together. Following the relevant legislation, standards, manufacturer instructions and engineering advice helps ensure that the selected arrangement is appropriate for the site.


Frequently Asked Questions

Is edge protection mandatory in Queensland?

Queensland's WHS Regulation requires suitable fall prevention controls for specified construction fall risks. Edge protection is one recognised control measure, but the appropriate system depends on the work and site conditions.

At what height is edge protection required in Queensland?

Specific fall prevention requirements apply at a fall risk of at least 3 metres in housing construction and at least 2 metres in other construction work. Separate requirements also apply to construction work on roofs with a slope greater than 26 degrees.

Does scaffolding need edge protection?

Scaffolding must have suitable fall protection for its design, configuration and intended use. Additional edge protection must not be fitted to a scaffold that was not originally designed, supplied or manufactured for it without the written engineer approval required by section 3.5.5 of Queensland's Scaffolding Code of Practice 2021.

Is a SWMS required for edge protection work?

A SWMS is required for high-risk construction work involving a risk of a person falling more than 2 metres. This requirement applies to housing and other construction work.

What Australian Standard covers temporary edge protection?

The AS/NZS 4994 series covers temporary edge protection, including general requirements, roof edges, non-roof edges and perimeter protection screens. The relevant part depends on the system and application.

Can roof safety mesh replace edge protection?

No. Roof safety mesh helps manage the risk of falling through roof sheeting, while perimeter edge protection addresses the risk of falling from the roof edge. Both may be needed depending on the work and site risk assessment.


Important information: This article is general information for builders and contractors. It is not legal advice, an engineering specification or a substitute for a site-specific risk assessment. Always check the current legislation, applicable standards, manufacturer instructions and advice from suitably qualified professionals before selecting or installing a fall protection system.

Comments


bottom of page